A-ARM Stretch Wrappers
(Cousins Exclusive)
Super Rapid Thread Pre-Stretch CarriageAutomatic Stretch
Wrappers
Semi-Automatic
Overhead Rotary
Arm Stretch Wrappers
Semi-Automatic
Turntable Stretch
Wrappers
All Categories > Automatic Stretch Wrappers > Conveyorized Overhead Automatics > Model 7100-65-OHA "HERCULES" Heavy Duty Conveyorized Overhead Automatic Stretch Wrap System  
    Printable Page     Email Email This Page     Save To Favorites Save To Favorites

Model 7100-65-OHA "HERCULES" Heavy Duty Conveyorized Overhead Automatic Stretch Wrap System







Specifications  · Features

Specifications

Production Speed

  • 1-65 loads per hour
    NOTE: Process rates will vary with load size, number of wraps & conveyor speed
  • Load Capacity

  • Maximum load weight: 4,000 lbs dynamic - 12,000 lbs static
  • Maximum load size: 50" W x 60" L (79" max. load diagonal) x 80" H (plus up to 4" top overlap)
  • Minimum load size: 30" W x 30" L x 24" H
  • Rotary Arm

  • 20" diameter ring bearing support system
  • ANSI # 60 direct chain drive c/w chain tensioner
  • 1-22 RPM rotational speed c/w soft start acceleration
  • Final revolution deceleration and positive stop alignment
  • 1 HP DC variable speed motor
  • Film Carriage Elevator

  • 3/4 HP DC variable speed motor
  • ANSI # 50 direct chain drive c/w shock dampeners
  • Maintenance free 12 point carriage guidance system
  • Film Delivery System

  • NEW Super Rapid Thread II ™ 20" capacity pre-stretch film carriage
  • Special Film Threading Device - Uniquely orientates the sticky side of the film against the pre-stretch rollers and the inside of the load.
  • 1/2 HP DC variable speed motor
  • Fully electronic dynamic dancer corner compensation
  • 33 to 313% fixed stretch capability
  • Pre-stretch ratio variable by easy sprocket change
  • Rapid Thread ™ Safety Door with auto power cut-off switch
  • Superior film-to-roller contact area
  • Lifetime warranty on pre-stretch rollers
  • Powered Roller Conveyor

    Basic system: 5ft infeed section, 12ft Process/wrap zone section and 5ft exit section

    Each section includes:
  • Chain driven live roller conveyor rated 4,000 lbs per section
  • 2-1/2" diameter 11 gauge rollers c/w 11/16" hex axles on 3" centers
  • All rollers ANSI # 40 chain driven, roller to roller
  • 54" effective roller width
  • Conveyor speeds 30 to 60 FPM (specify required speed) with electronic soft start
  • Pass-line height - 18" from floor to top of rollers
  • 3/4 HP AC variable speed reversible TEFC motor on infeed & outfeed conveyors / 1 HP AC variable speed reversible TEFC motor on process conveyor
  • Automatic load indexing and centering by photo-eye & PLC logic
  • Electrical Input Requirement

  • 230 or 460 Volts 3 Phase 60 Hz 30 Amps (required voltage to be specified) (other voltages available - consult factory)
  • Pneumatic Requirement

  • 3 CFM @ 80 PSI clean dry pneumatic supply required
  • Filter/regulator c/w gauge & lock-out valve provided
  • Typical System Dimensions

  • 264" (L) x 167" (W) x 140" (H) (Overall includes conveyor (L) and Control panel (W) - all dimensions approximate)


  • Features

    Control Features

  • Allen-Bradley MicroLogix 1400 Programmable Logic Controller (PLC) with built-in EtherNet/IP communications
  • HMI Touchscreen Operator Interface Panel
  • Illuminated Power Start / Reset button
  • Emergency Stop button
  • Wrap Cycle Start (rewrap) button
  • Manual controls provided for rotary arm jog, film carriage elevator lower/raise, film clamp open/close and conveyors forward/reverse
  • Wrap Bypass mode selector switch
  • Separate film carriage elevator raise & lower speed controls
  • Film tension (Force-to-Load) control
  • Separate 1 to 12 revolution top & bottom wrap control
  • Triple beam auto load height sensing photo-eye, detects dark or shiny loads
  • Broken film/out of film detection c/w automatic machine reset and fault beacon light
  • Rotary arm and film carriage elevator dynamic braking
  • NEMA 12 control panel and junction boxes
  • Dust tight slip ring assembly
  • Non-proprietary UL/CSA approved components
  • Automation Features

  • Pneumatically actuated film clamp mechanism
  • Pneumatically actuated film tail cut/wiper arm mechanism
  • Ni-chrome impulse hot wire film cut off c/w automatic periodic cleaning cycle
  • Structural Features

  • All structural steel construction
  • Structural tube machine tower & frame
  • Electro-static powder coated paint finish
  • Safety Features

  • Personnel Safety - Rotary Arm Obstruction Emergency Stop Sensor
  • Wire mesh safety barriers enclose the wrap zone to prevent personnel intrusion
  • Operator Access Gates c/w Safety Interlock Switches disable machine operation when gate(s) opened
  • Hard-wired emergency stop and operator access gate circuits with Category 3 dual channel safety relays


  •  DOWNLOADS 

    7100
    (PDF, 619KB)

    Dimensional Drawing for Model 7100-65-OHA HERCULES Heavy Duty Conveyorized Overhead Automatic Stretch Wrap System
    (PDF, 132KB)

    Specifications for Model 7100-65-OHA HERCULES Heavy Duty Conveyorized Overhead Automatic Stretch Wrap System
    (PDF, 112KB)